Comparison of Heat Transfer Performance of Lattice-Structured Heat Sinks
DOI:
https://doi.org/10.35806/djhqed26Keywords:
Finite element analysis, Heat sink, Heat transfer, Lattice structures, Steady state thermalAbstract
This paper presents a comparative study of the heat transfer performance of lattice-structured heat sinks. Twenty different unit cells are chosen, and heat sinks are modeled in nTop with constant unit cell size. Al 6061 alloy is chosen as the material for analysis due to its good thermal conductivity, low weight, low cost, and high strength. Steady-state thermal analysis is performed using ANSYS with constant input parameters for all samples. Heat flux and temperature distribution within the heat sinks are analyzed. From the simulation, it was found that TPMS and plate-based heat sinks outperform other types with better heat transfer.
References
Abou-Ali, A., Lee, D.-W., & Abu Al-Rub, R. (2022). On the Effect of Lattice Topology on Me-chanical Properties of SLS Additively Manufactured Sheet-, Ligament-, and Strut-Based Polymeric Metamaterials. Polymers, 14, 4583. https://doi.org/10.3390/polym14214583
Andrew, J., Alhashmi, H., Schiffer, A., Kumar, S., & Deshpande, V. (2021). Energy absorption and self-sensing performance of 3D printed CF/PEEK cellular composites. Materials & Design, 208, 109863. https://doi.org/10.1016/j.matdes.2021.109863
Arefin, A. M. E. (2016). Thermal analysis of modified pin fin heat sink for natural convection. 2016 5th International Conference on Informatics, Electronics and Vision (ICIEV), 1–5. https://doi.org/10.1109/ICIEV.2016.7759986
Benedetti, M., du Plessis, A., Ritchie, R. O., Dallago, M., Razavi, N., & Berto, F. (2021). Archi-tected cellular materials: A review on their mechanical properties towards fatigue-tolerant design and fabrication. Materials Science and Engineering: R: Reports, 144, 100606. https://doi.org/https://doi.org/10.1016/j.mser.2021.100606
Bhate, D., & Hayduke, D. (2023). Architected Cellular Materials. In M. Seifi, D. L. Bourell, W. Frazier, & H. Kuhn (Eds.), Additive Manufacturing Design and Applications (Vol. 24A, p. 0). ASM International. https://doi.org/10.31399/asm.hb.v24A.a0006951
Bouville, F., Maire, E., Meille, S., Van de Moortèle, B., Stevenson, A. J., & Deville, S. (2014). Strong, tough and stiff bioinspired ceramics from brittle constituents. Nature Materials, 13(5), 508–514. https://doi.org/10.1038/nmat3915
Bury, T., & Hanuszkiewicz-Drapala, M. (2018). Evaluation of selected methods of the heat transfer coefficient determination in fin-and-tube cross-flow heat exchangers. MATEC Web of Conferences, 240, 2004. https://doi.org/10.1051/matecconf/201824002004
Catchpole-Smith, S., Sélo, R., Davis, A. W., Ashcroft, I., Tuck, C., & Clare, A. (2019). Thermal Conductivity of TPMS Lattice Structures Manufactured via Laser Powder Bed Fusion. Additive Manufacturing, 30, 100846. https://doi.org/10.1016/j.addma.2019.100846
D. V. Abramkina, Abramyan, A. A., & Shevchenko-Enns, E. R. (2018). Experimental determi-nation of convective heat transfer coefficients in thermal buoyacy ventilation system. Herald of Dagestan State Technical University., 45(4), 133–144.
Dewan, A., Patro, P., Khan, I., & Mahanta, P. (2010). The effect of fin spacing and material on the performance of a heat sink with circular pin fins. Proceedings of The Institution of Mechanical Engineers Part A-Journal of Power and Energy - PROC INST MECH ENG A-J POWER, 224, 35–46. https://doi.org/10.1243/09576509JPE750
Dong, G., Tang, Y., & Zhao, Y. F. (2017). A Survey of Modeling of Lattice Structures Fabricat-ed by Additive Manufacturing. Journal of Mechanical Design, 139(10). https://doi.org/10.1115/1.4037305
Erdoğdu, F. (2008). A review on simultaneous determination of thermal diffusivity and heat transfer coefficient. Journal of Food Engineering, 86(3), 453–459. https://doi.org/https://doi.org/10.1016/j.jfoodeng.2007.10.019
Fayolle, P. A., Fryazinov, O., & Pasko, A. (2017). Rounding, filleting and smoothing of implicit surfaces. Computer-Aided Design and Applications, 15, 1–10. https://doi.org/10.1080/16864360.2017.1397890
Grądziel, S., Majewski, K., & Majdak, M. (2019). Experimental determination of the heat transfer coefficient in internally rifled tubes. Thermal Science, 23, 1163–1174. https://doi.org/10.2298/TSCI19S4163G
Guo, X., Zheng, X., Yang, Y., Yang, X., & Yi, Y. (2019). Mechanical behavior of TPMS-based scaffolds: a comparison between minimal surfaces and their lattice structures. SN Ap-plied Sciences, 1(10), 1145. https://doi.org/10.1007/s42452-019-1167-z
Jia, Z., Liu, F., Jiang, X., & Wang, L. (2020). Engineering lattice metamaterials for extreme property, programmability, and multifunctionality. Journal of Applied Physics, 127, 150901. https://doi.org/10.1063/5.0004724
Jia, Z., Yu, Y., & Wang, L. (2019). Learning from nature: Use material architecture to break the performance tradeoffs. Materials and Design, 168, 107650. https://doi.org/10.1016/j.matdes.2019.107650
Korprasertsak, N., & Leephakpreeda, T. (2017). Real-Time Determination of Convective Heat Transfer Coefficient Via Thermoelectric Modules. Journal of Heat Transfer, 139. https://doi.org/10.1115/1.4036734
Kushwaha, A. S. & Kirar, R. (2013). Comparative Study of Rectangular, Trapezoidal and Par-abolic Shaped Finned Heat sink. IOSR Journal of Mechanical and Civil Engineering, 5, 1–7. https://doi.org/10.9790/1684-0560107
Li, Q., Hong, Q., Qi, Q., ma, X., Han, X., & Tian, J. (2018). Towards additive manufacturing oriented geometric modeling using implicit functions. Visual Computing for Industry, Biomedicine, and Art, 1. https://doi.org/10.1186/s42492-018-0009-y
McGregor, Martine, Sagar Patel, Stewart McLachlin, and Mihaela Vlasea. "Architectural bone parameters and the relationship to titanium lattice design for powder bed fusion additive manufacturing." Additive Manufacturing 47 (2021): 102273. http://dx.doi.org/10.1016/j.addma.2021.102273
Moreira, T., Colmanetti, A. R., & Tibiriçá, C. (2019). Heat transfer coefficient: a review of measurement techniques. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 41, 264. https://doi.org/10.1007/s40430-019-1763-2
Nazir, A., Mekonen, K., Kumar, A., & Jeng, J.-Y. (2019). A state-of-the-art review on types, design, optimization, and additive manufacturing of cellular structures. The Interna-tional Journal of Advanced Manufacturing Technology, 104. https://doi.org/10.1007/s00170-019-04085-3
Opalach, A., & Maddock, S. (1995). An Overview of Implicit Surfaces.
Pei, E., Kabir, I., Breški, T., Godec, D., & Nordin, A. (2022). A review of geometric dimension-ing and tolerancing (GD&T) of additive manufacturing and powder bed fusion lattices. Progress in Additive Manufacturing, 7. https://doi.org/10.1007/s40964-022-00304-8
Perween, S., Fahad, M., & Khan, M. (2021). Systematic Experimental Evaluation of Function Based Cellular Lattice Structure Manufactured by 3D Printing. Applied Sciences, 11, 10489. https://doi.org/10.3390/app112110489
Pronk, T. N., Ayas, C., & Tekoğlu, C. (2017). A Quest for 2D Lattice Materials for Actuation. Journal of the Mechanics and Physics of Solids, 105. https://doi.org/10.1016/j.jmps.2017.05.007
Ritchie, R. O. (2011). The conflicts between strength and toughness. Nature Materials, 10(11), 817–822. https://doi.org/10.1038/nmat3115
Schaedler, T. A., & Carter, W. B. (2016). Architected Cellular Materials. Annual Review of Materials Research, 46(Volume 46, 2016), 187–210. https://doi.org/https://doi.org/10.1146/annurev-matsci-070115-031624
Shah, S. I. (2016). Effect of geometry and arrangement of pin fin in heat exchanger: A re-view. International Journal of Emerging Technologies and Innovative Research, 3(2), 39–43.
Talebi, S., R. Hedayati, and M. Sadighi. "Dynamic crushing behavior of closed-cell aluminum foams based on different space-filling unit cells." Archives of Civil and Mechanical En-gineering 21, no. 3 (2021): 99. http://dx.doi.org/10.1007/s43452-021-00251-1
Tancogne-Dejean, T., Diamantopoulou, M., Gorji, M. B., Bonatti, C., & Mohr, D. (2018). 3D Plate-Lattices: An Emerging Class of Low-Density Metamaterial Exhibiting Optimal Iso-tropic Stiffness. Advanced Materials, 30(45), 1803334. https://doi.org/https://doi.org/10.1002/adma.201803334
Tyagi, Shivank A., and M. Manjaiah. "Additive manufacturing of titanium-based lattice struc-tures for medical applications–a review." Bioprinting 30 (2023): e00267. https://doi.org/10.1016/j.bprint.2023.e00267
VOICU, Andrei Daniel, Anton Hadăr, and Daniel Vlăsceanu. "Benefits of 3D printing technol-ogies for aerospace lattice structures." Scientific Bulletin'Mircea cel Batran'Naval Academy 24, no. 1 (2021). http://dx.doi.org/10.21279/1454-864X-21-I1-001
Yardi, A., Karguppikar, A., Tanksale, G., & Sharma, K. (2017). Optimization of fin spacing by analyzing the heat transfer through rectangular fin array configurations (natural con-vection). International Research Journal of Engineering and Technology, 4(9).
Downloads
Published
Versions
- 2024-10-03 (2)
- 2024-10-01 (1)
